Vitamix blade removal tool

As mentioned earlier in the article, the Vitamix blade removal wrench is the best tool to use when removing your Vitamix assembly. It is long enough to reach the bottom of your Vitamix container hence keeping your hands safe from the sharp blades. Additionally, if your blade is broken, the wrench helps prevent further damage to the blades and ensure that there are no sharp edges to interact with while removing the blade. Most blending blade removal wrenches purchased from amazon are compatible with all Vitamix blender jars.

Yes, you can remove your Vitamix blade assembly without the wrench. However, you have to take extra precautions not to injure your hands with the ultra-sharp blades.

If you are using a screwdriver, place it horizontally across one lob slot on the retainer. Remember to keep your fingers as far as possible from the blades. Turn the retainer nut anticlockwise. Avoid using a lot of pressure when turning the retainer nut to avoid damaging or breaking your blender container or the blade assembly.

Use a thick piece of cloth to reach for the retainer nut. The nut is large enough for you to grasp. Using your first finger and your thumb, turn the retainer nut anticlockwise and remove it slowly. Then turn your Vitamix container right side up and lift out the blade assembly safely using the thick piece of cloth.

The apparent reason that would make you remove the Vitamix blade assembly is when you need to do some thorough cleaning. Vitamix blenders hide food particles between and beneath the blades. If left uncleaned, the food particles develop microorganisms that could cause food poisoning. Read More: How to clean your Vitamix blender. When blending, food may get stuck between the blades in areas you may not reach. The blades consequently stop turning, and you cannot go ahead with your blending.

You will be forced to remove your Vitamix blade assembly to remove the stuck food and check out any other underlying condition. Vitamix blades may wear out with time, and it may be hard for you to blend. Additionally, your blender may blow up because of using faulty blades. Yes, Vitamix provides its consumers with a guide on removing the Vitamix blade assembly in the user manual.

Suppose you have lost or misplaced your user manual handbook; no need to panic. You can also download it and print it. Just like any other kitchen appliance, Vitamix blenders need proper maintenance. This means thorough cleaning and replacement of the blades if damaged. Ensure that the blender is disconnected from the power socket before removing the Vitamix blade. You cannot use this appliance again until you remove that blade, but how do you do it without causing any damage to either yourself or your expensive machine?

In this post, we will show you how to remove the Vitamix blade easily by using a screwdriver or by using a specialized tool by Vitamix! Turn your Vitamix upside down on a flat surface, so you are able to get at its bottom more easily. To release the retaining nut, locate it at the bottom of your container and look for a large silver round disk.

Notice that this has two slots on its lip which are about one inch in width; these should be opposite the other across from each other. If you have a screwdriver, this is what to do for the next step. Lay it horizontally across one of the lob slots on the retainer nut and make sure that its shaft rests against the center drive spline in between two prongs at top of the ratchet head where the lever would normally be.

To unscrew the blade, hold the container securely in your hands and turn counterclockwise with the screwdriver. The shaft of the screwdriver will twist this nut to loosen its grip on the drive spline that connects them both- use leverage by turning horizontally while making sure not to put too much pressure on one side or you may break something!

Remove the retainer nut from the container by using your hands. Turn upside down and place a thick cloth over blades inside of bottom, then grasp with a blanket to lift out safely. The Vitamix Blade Removal Tool is a great tool for those who are struggling to remove blades on their own.

This handy little Vitamix tool to remove blade has been designed in such a way so as not only provides some form of mechanical advantage but also reduces slipping which can be common while trying this yourself without help.

Not only does this tool make blade removal quick and easy, but it also helps you avoid cuts or scrapes on your hands! The Vitamix blade wrench makes the process of detaching a broken blade safe by making sure that there are no sharp edges to contend with. The Vitamix Blade Removal Tool is the perfect accessory for anyone with a Vitamix who needs to clean their blades.

If you wanted to remove the Vitamix blade because they had become dull, and did not function properly, here is a step by step guide to change Vitamix blades with new ones after removing them using the above steps —.